gasraterra.blogg.se

Cp210x usb to uart bridge driver installer for windows 2000
Cp210x usb to uart bridge driver installer for windows 2000





  1. CP210X USB TO UART BRIDGE DRIVER INSTALLER FOR WINDOWS 2000 INSTALL
  2. CP210X USB TO UART BRIDGE DRIVER INSTALLER FOR WINDOWS 2000 SERIAL
  3. CP210X USB TO UART BRIDGE DRIVER INSTALLER FOR WINDOWS 2000 DRIVERS
  4. CP210X USB TO UART BRIDGE DRIVER INSTALLER FOR WINDOWS 2000 DRIVER

  • The COM port number assigned to your instrument may vary from computer to computer, or even on the same computer (rarely).
  • Multiple instruments can be connected to the same computer,Īnd Windows automatically assign them to different COM ports.

    CP210X USB TO UART BRIDGE DRIVER INSTALLER FOR WINDOWS 2000 DRIVER

    The USB driver needs to be installed only once on your computer.For older models without this switch, you may need to change a jumper setting instead. To use USB, the white switch on the instrument rear panel must be flipped toward the USB port.

    CP210X USB TO UART BRIDGE DRIVER INSTALLER FOR WINDOWS 2000 DRIVERS

    Rebooting your computer immediately after uninstalling drivers may also help, especially in Windows XP and earlier.If at this point a COM port is still assigned, you may also need to uninstall the driver from Control Panel > Programs and Features and repeat the procedure above.The Cygnal or CP210x composite device should also no longer be installed. To confirm that the USB driver is fully uninstalled, disconnect and reconnect the instrument to your computer and make sure that the CP210x device is now listed under Other devices as shown here.

    CP210X USB TO UART BRIDGE DRIVER INSTALLER FOR WINDOWS 2000 SERIAL

  • If present, you will also need to do this for a "Cygnal USB Composite Device" or "CP210x USB Composite Device" under the Universal Serial Bus Controllers category as shown here.
  • Right-click on the CP210x COM device in Device Manager and click Uninstall (check "Delete the software driver for this device" when prompted).
  • To do this not only for the COM Port, but also a USB Composite Device. To uninstall any previously installed drivers, right-click on the device in Device Manager and click Uninstall. To confirm that the instrument and computer are communicating properly. Using the System command under the Setup menu, and then run the Hardware Test command under the Setup menu Assign this number in your instrument software, Take note of the COM port number (COM5 in the example above).
  • Locate "CP210x USB to UART Bridge Controller" or a similarly named device to verify successful installation.
  • Double-click the category "Ports (COM & LPT)" to display:.
  • Open Device Manager (right-click Computer > Manage > Device Manager).
  • Wait for any automatic system installation tasks to complete.
  • Connect the instrument to your PC and turn the power on.
  • Disconnect the instrument from your PC, if applicable.
  • First complete the USB Driver installation procedure above.
  • Please note that the latest driver requires our software version 12.04 or newer.
  • Windows should now recognize the instrument automatically.
  • Finally, power on and connect your instrument to your computer.
  • Restart your computer if prompted to do so.
  • CP210X USB TO UART BRIDGE DRIVER INSTALLER FOR WINDOWS 2000 INSTALL

  • This should install files in two locations.
  • Make sure the "Launch the CP210x VCP Driver Installer" option is checked, when it appears.
  • Follow the on-screen instructions, accepting all default options in the affirmative.
  • Download and run (double-click) the file "CP210x_latest.exe" from the link above.
  • Do not connect the instrument to the computer yet.
  • If you are using an older version of our software or Windows, please visit our Legacy Downloads page.
  • CH Instruments Software version 12.04 or newer (Help > About).
  • Administrative privileges on your computer (please consult your system administrator for details).
  • Experimental support for Linux and (Mac) OS X is described on a separate page.
  • Both 32-bit and 64-bit versions of Windows are supported.






  • Cp210x usb to uart bridge driver installer for windows 2000